![9mm mac 10 9mm 9mm mac 10 9mm](https://s3.amazonaws.com/mgm-content/sites/armslist/uploads/posts/2017/01/09/6310744_01_mac_10_cobray_m_11_9mm_640.jpg)
Noting the weapon's poor precision, in the 1970s, International Association of Police Chiefs weapons researcher David Steele described the MAC series as "fit only for combat in a phone booth".
![9mm mac 10 9mm 9mm mac 10 9mm](https://dwsuk.org/WebRoot/Store15/Shops/057184c7-2fa2-4321-880c-a30e87657239/54C2/2CB3/36B8/72D0/0A55/0A48/3537/2AAC/mac10n220084d.jpg)
That of the 9mm is approximately 1250, and that of the smaller MAC-11 in. 45 ACP is approximately 1090 rounds per minute. The original rate of fire for the M10 in. Ingram added a small bracket with a small strap beneath the muzzle to aid in controlling recoil during fully automatic fire. At the suggestion of the United States Army, the suppressor also acts as a foregrip to inhibit muzzle rise when fired. 45 ACP versions, as most loads are subsonic already, as opposed to special, low-powered subsonic loads usually required for suppressed 9mm weapons. The barrel is threaded to accept a suppressor, which works by reducing the discharge's sound without attempting to reduce the speed of the bullet. In addition, this design incorporates a built in feed ramp as part of the trigger guard (a new concept at the time) and, to save on cost, the magazine was recycled from the M3 Grease Gun. The M10 fires from an open bolt, and the light weight of the bolt results in a rapid rate of fire. This allows a more compact weapon and balances the weight of the weapon over the pistol grip, where the magazine is located. The M10 has a telescoping bolt, which wraps around the rear face of the barrel. A notched cocking handle protrudes from the top of the receiver, and turns the handle 90°, locks the bolt, and acts as an indicator the weapon is unable to fire. The M10 is built predominantly from steel stampings. Military Armament Corporation never used the nomenclature MAC-10 on any of its catalogs or sales literature, but because "MAC-10" became so frequently used by Title II dealers, gun writers, and collectors, it is used more frequently than "M10" to identify the gun. The term "MAC-10" is commonly used in unofficial parlance. under the assault weapons ban enacted by Congress in 1994. For a decade, the semi-automatic pistol version of the weapon was forbidden in the U.S.
#9MM MAC 10 9MM FULL#
A two-stage suppressor by Sionics was designed for the MAC-10, which not only abates the noise created, but makes it easier to control on full automatic (although it also makes the gun far less compact and concealable). The Military Armament Corporation Model 10, officially abbreviated as " M10" or " M-10", and more commonly known as the MAC-10, is a compact, blowback operated machine pistol/ submachine gun that was developed by Gordon B.
![9mm mac 10 9mm 9mm mac 10 9mm](https://www.gunsamerica.com/UserImages/3310/967186544/wm_11833518.jpg)
Any insight on doing a Form 1 build on a can like this? Would it be possible to use one of the fake cans available all over the place such as this one linked below? Looks like the endcaps can come off but idk if its just a hollow tube or what. That may be the easiest and quickest way to get my hands on a can in this style, the advantage is I could put modern guts into it, but I don't have a mill, lathe, or the technical skills to make a tube with the two diameters and thread it and everything, so it would have to be a custom job I'd have to send out to someone I guess.
#9MM MAC 10 9MM FREE#
How available are these things, should I just keep waiting? If I find one, what is a fair price to pay? I've seen some people say they've become collectible, others say that they basically are free with the price of the gun, so I have no real gouge on what the price should be.įinally, I've found one forum post on here from 6 years ago referencing doing a Form 1. I want the retro look more than I care about max performance. I understand these cans are pretty mediocre in comparison to modern options. 45ACP but the thread pitch is wrong, I've been completely unable to find one in 9mm with the 3/4 x 10 thread pitch. I just purchased my first machinegun, a MAC-10 in 9mm, and I want an original style two stage suppressor for it.